TekBox TBL50100-1B

Code: TBL50100-1B

50 µH 100 A line impedance stabilisation network LISN

In Stock 2-3 Weeks
Enquire Now

Description

The TBL50100-1B is a single path 50µH (+5 Ω) // 50 Ω LISN for conducted emission measurements of DC or AC-powered electronic equipment. It is designed according to CISPR 16-1-2 and MIL-STD-461G standards and characterized in the frequency range of 10 kHz to 100 MHz.

Setting a high current jumper shorts the 5 Ohm resistor and configures it as 50Ω // 50µH LISN according to CISPR 16-1-2. Removing the jumper configures the LISN to (50µH + 5 Ω) // 50 Ω for MIL-STD application. The LISN is characterized from 10 kHz to 100 MHz.

Combining two LISN with the Tekbox LISN Mate enables separate measurement of common mode and differential mode noise. EUTs with 3 phase supply require three or four pieces of TBL50100-1B, depending on whether the product is supplied in delta or star configuration.

An exposed bottom panel enables convenient ground plane connection. The unit comes equipped with a N-male to N-male RG223 cable.

SPECIFICATIONS

  • LISN type: single path V-AMN, configurable (jumper) as 50Ω/50µH+5 Ω or 50Ω/50µH; no 250µH pre-filter
  • Characterized Frequency range: 10 kHz – 100 MHz
  • DC Resistance: < 20 mΩ
  • Maximum current: 82 A continuous, 100A for 15 minutes; see heat up characteristics plot
  • Maximum operating voltage range: 0 – 500V DC; 0 – 270V AC (50/60 Hz), 0 – 120V AC (400 Hz)
  • EUT connector: binding post M8, 4mm center hole, 100A, 1kV, Schützinger POL 102 L / RT
  • SOURCE connector: binding post M8, 4mm center hole, 100A, 1kV, Schützinger POL 102 L / RT
  • Earth: 8mm Earth stud with wing-nut, exposed stainless steel bottom panel with mounting slots and countersunk hole for 4mm screw
  • RF connector: N-Female
  • Jumper: Harwin D3087-98
  • Dimensions: W x H x L; 230 mm x 230 mm x 350 mm;
  • Weight: 5.3 kg

APPLICATION

EMC pre-compliance testing of conducted noise

Model Overview

Model Impedance Frequency Range Path(s) Max. Current Max. Voltage Additional Features
TBL00705-2 0.7 µH//50 Ω 30 Hz – 500 MHz 2 5 A 60 V nominal, Component rating: 100 V 400 mΩ serial resistor
TBL0110-2 1 µH//50 Ω 30 Hz – 500 MHz 2 10 A 60 V nominal, Component rating: 100 V 100 mΩ serial resistor
TBL0225-2 2 µH//50 Ω 10 Hz – 200 MHz 2 25 A 60 V nominal, Component rating: 100 V 100 mΩ serial resistor
TBL0225-2B 2 µH//50 Ω 10 Hz – 200 MHz 2 25 A 100 V nominal, Component rating: 100 V 100 mΩ series resistor and internal 10,000 µF capacitor
TBL0510-1 5 µH//50 Ω 10 kHz – 400 MHz 1 10 A 60 V nominal, Component rating: 200 V •
TBL0550-1B 5 µH//50 Ω 10 kHz – 400 MHz 1 50 A 0 – 250 V AC @ 50/60 Hz, 130 V AC @ 400 Hz, 250 V DC 450 CV DC (components) Can be jumpered to various standards
TBL05100-1C 5 µH//50 Ω 10 kHz – 400 MHz 1 100 A 0 – 500 V AC @ 50/60 Hz, 250 V AC @ 400 Hz, 1500 V DC (components) Can be jumpered to various standards
Model Impedance Frequency Range Path Max. Current Max. Voltage Additional Features
TBL5032-1 50Ω/50µH+5Ω//50Ω/50µH 10 kHz – 100 MHz 1 32 A 500 V DC / 270 V AC (50/60 Hz)
120 V AC (400 Hz)
can be jumpered 50µH//50Ω or (50µH+5Ω)//50Ω no 250uH pre-filter
TBL50100-1B 50Ω/50µH+5Ω//50Ω/50µH 150 kHz – 30 MHz 1 82 A 0 – 500V DC; 0 – 270V AC (50/60 Hz),
0 – 120V AC (400 Hz)
can be jumpered 50µH//50Ω or (50µH+5Ω)//50Ω no 250uH pre-filter
TBL501000-1 50µH // 50 Ω 100 kHz – 30 MHz 1 1000 A 0 – 1000 V DC; 0 – 500 V AC (50/60 Hz)
TBL5008-2B (50µH+5Ω)//50Ω 9 kHz – 30 MHz 2 8 A 250V AC 50/60 Hz or DC separate RF outputs enabling LISN-Mate connectivity; Artificial hand connection PE switchable: 50Ω//50µH
TBL5008-2C (50µH+5Ω)//50Ω 9 kHz – 30 MHz 2 8 A 250V AC 50/60 Hz or DC Filter/Limiter/Attenuator switchable Artificial hand connection PE switchable: 50Ω//50µH
TBL5016-1 (50µH+5Ω)//50Ω 150 kHz – 30 MHz 1 16 A 250V AC 50/60 Hz or DC EOL, replaced by TBL5032-1
TBL5016-2B (50µH+5Ω)//50Ω 9 kHz – 30 MHz 2 16 A 250V AC 50/60 Hz or DC separate RF outputs enabling LISN-Mate connectivity; Artificial hand connection PE switchable: 50Ω//50µH
TBL5016-2C (50µH+5Ω)//50Ω 9 kHz – 30 MHz 2 16 A 250V AC 50/60 Hz or DC Filter/Limiter/Attenuator switchable Artificial hand connection PE switchable: 50Ω//50µH
TBL5016-3 (50µH+5Ω)//50Ω 9 kHz – 30 MHz 3 16 A 465V/270V Artificial hand connection PE switchable: 50Ω//50µH
TBL5032-3 (50µH+5Ω)//50Ω 9 kHz – 30 MHz 3 32 A 465V/270V Artificial hand connection PE switchable: 50Ω//50µH
TBL5063-3 (50µH+5Ω)//50Ω 9 kHz – 30 MHz 3 63 A 690V/400V 50Hz/60Hz Artificial hand connection PE switchable: 50Ω//50µH
Model Impedance Frequency Range Path Max. Current Max. Voltage Additional Features
TBLM2 • 150 kHz – 110 MHz • • • LISN-Mate
TBLDC32-2 150 Ohm 9 kHz – 30 MHz 2 32A 1000V DC 150 Ohm DC LISN A, B,
Common-Mode Differential-Mode operation
TBLVHF-B 50 Ohm +-10% 30 MHz – 300 MHz 2 16A 250V DC – 400 Hz Balanced VHF LISN
TBISN-T4 150 Ohm 150 kHz – 30 MHz 2 balanced pairs 250mA 60V AC, 100V DC 2 pcs D-Sub 25 to RJ45 adapter

Downloads

Datasheet


Adobe PDF

TBL50100-1B Datasheet

Language: English
Version: V1.0
File Size: 1.75 MiB
Release Date: 29.06.2026

Guide


Adobe PDF

EMC pre compliance testing guide EN

Language: English
Version: V1.2
File Size: 406.81 KiB
Release Date: 30.04.2018
This document focusses on measurement equipment and methods, limits and the relevant standards of conducted noise measurement on the power supply lines of products. The document tries to reduce the details to those necessary to carry out pre-compliance measurements in house with modest equipment.

Adobe PDF

EMC pre compliance testing guide German

Language: German
Version: V1.7
File Size: 402.40 KiB
Release Date: 12.10.2022
This document focusses on measurement equipment and methods, limits and the relevant standards of conducted noise measurement on the power supply lines of products. The document tries to reduce the details to those necessary to carry out pre-compliance measurements in house with modest equipment.

Reviews

There are no reviews yet.

Be the first to review “TekBox TBL50100-1B”

Your email address will not be published. Required fields are marked *